What to do with an iPhone that has been dropped into water or water has flowed under the screen? Large manual instructions. What to do if your phone falls into water and does not turn on

Did your phone fall into the water? It doesn’t matter if you immediately take the right steps so that it works as before it fell into the ill-fated liquid. Unfortunately, if a phone is in water, it loses its warranty, even if you bought it yesterday or today. Therefore, the resuscitation of a cell phone should be approached thoroughly, after The phone is wet.

After water gets into a mobile phone, it may still work for some time, but this does not mean that everything is in order, because negative consequences will affect it later.

1. If suddenly your phone fell into water, try to get it out as quickly as possible, because if the phone fell for a few seconds, then the water did not have time to seep to the deepest mechanisms, but if your phone has been spinning in the washing machine for more than an hour, then most likely you will have to say goodbye to it, but try to revive it it's still worth it.

2. After your phone got wet, it must be turned off immediately. Even if it still works, it's too early to judge the integrity of its functionality. All the buggies can come out later, when you have already forgotten about the phone falling into the water.

3. Immediately disconnect the battery (accumulator). After all, water can cause a short circuit, which can result in the microcircuits burning out. If possible, disassemble it as much as possible. If you disconnect the battery immediately after dropping the phone into water, you can save the battery.

4. Then you need to remove the SIM card: if you store information about contacts on it, and if you can’t save the phone after it fell into the water, then at least you can save some of the data.

5. After all parts of the phone are disconnected from each other, carefully wipe them with paper napkins to absorb excess moisture. Then you need to leave the phone disassembled to dry. There is no need to dry your phone with a hairdryer, on batteries or in the sun; heating can damage the microcircuits and wiring in the phone. Place your phone in a warm, dry place. You should not turn on the phone before it is completely dry to make sure it is working. You can only harm him. If the phone fell into the water for just a couple of seconds, then about one day is enough to dry it. It is better, of course, not to touch the phone for a week, it will be more reliable.

Some popular advice says that if the phone falls into water, it should be immersed in alcohol, after first disconnecting the battery. The water will evaporate along with the alcohol, and the alcohol will clean the board of oxidation and salt contamination. Under no circumstances should you treat your phone with vodka or cologne: these are aqueous solutions of alcohol and you will only speed up the corrosion process.

People's advice also says that it is possible to dry a phone after it has fallen into water using rice. To do this, the battery and SIM card are removed from the phone, and the phone is placed in a container filled with ordinary rice. Rice absorbs moisture, and accordingly, the drying process of the phone speeds up. The phone should be kept in a container with rice for several days, and only then you can try to turn it on.

If your mobile phone has been in coffee, champagne, juice, beer, etc. then it is best, after you have separated all its parts, to rinse the phone with alcohol and then dry it.

And finally, the most useful advice is that if after you have dried the phone and it does not turn on, you should contact a specialist. Perhaps repairing your phone will cost pennies and you won’t have to buy a new one. And most importantly, it is possible to recover valuable information from your phone: contacts, photos and videos.

P.S. Don't drop your phones in the water and don't forget to subscribe to new articles.

Dropping a mobile phone into liquid is a fairly common cause of breakdowns. What to do if Most problems in the operation of this device begin with moisture getting inside. Of course, the severity of the breakdown will depend on the type of liquid, how long its contact with the microcircuits lasted and whether the mobile phone was turned on. Has your phone fallen into water and won't turn on? We will solve the problem promptly. When your mobile device decides to take a bath, the first things to suffer are the microphones, speakers and circuits. And the nature of the breakdown directly depends on the model and manufacturer.

What are the dangers of water getting into your phone? So, what awaits you: keyboard sticking; battery malfunctions; metal parts begin to rust; the screen flashes; the speaker wheezes, etc. In other words, if you do not take the necessary measures in the first minutes, then repairing your phone after water damage is inevitable. Why can't you turn on your cell phone? Water is known to be an excellent conductor for electricity. When you try to turn on the device, an electrical signal will be given, the water will pick it up and short-circuit all the microcircuits. This will happen and all the circuits will fail completely. You also need to remember that water is a good oxidizing agent, and with additional exposure to electric current, metal corrosion processes only intensify.

What to do if your phone falls into water? The first step is to remove the battery. Under no circumstances should you try to check if the phone is working by trying to turn it on. To remove liquid from the mobile phone body as efficiently as possible, you need to “unfasten” it as much as possible: remove all panels, remove the battery, remove the SIM card and the additional one (flash card). It is not advisable to shake your mobile phone: some contacts may come off. The phone must be dried, but under no circumstances with hot air from a hair dryer. Hot will also not work. Under the constant flow of high temperatures, delicate microcircuits can begin to melt. Any hair dryer has cool air functions, so this is an ideal option. If it is not possible to dry it with an air stream, then you can place the device next to a working heating radiator.

What to do if your phone falls into water? The rule is the following. Many people have heard about the property of rice to absorb moisture, especially housewives. They know that the readiness of the grains is symbolized by their size, which increases by at least one and a half times due to water. The amount of moisture absorbed depends on the type of rice. We need a container with a lid. We pour regular rice into it and put the mobile phone from which the case has been removed. Close the lid and forget about it for a few days (at least). The rice will absorb the remaining moisture that remains in the phone even after trying to blow it out with a warm stream of air from a hairdryer. This is just one answer to the question “what to do if your phone falls into water.”

If after simple procedures the mobile phone does not work, then show it to the technician at the service center as soon as possible. He will determine the exact cause of the breakdown and try to bring the device back to life by replacing important parts.

Modern mobile devices do not get along with moisture at all. But since he is almost always with us, at work, on walks and in the bathroom, it is not always possible to protect him from contact with liquid. A puddle, a washing machine, tea, a pond... All this can separate us from our favorite gadget. You usually don’t want to be separated, so it’s logical to ask the question. How to save a phone that has fallen into water?
If your phone falls into the water, and the option of throwing it away and forgetting is not considered at all, you will have to rescue it.

What to do if your phone falls into water

• After phone fell into water, it must be removed from there immediately. The less time he spent in a puddle or in the washing machine, the greater the chance of his recovery. If the device does not turn off on its own after contact with liquid, it must be turned off immediately. The fact that it is working now does not guarantee that it will not “die” in 20 minutes.
• It is still possible to save a purchased device, the main thing is not to panic and know what and how to do correctly.
• After turning off, remove all liquid from the surface. Use napkins, towels, toilet paper, whatever is at hand, there is no choice. Next you need to remove all the parts that can be removed. First of all, remove the battery. This way you can still save it from moisture and oxidation.
• In addition, you need to remove the protective film from the screen and take out the SIM card.
• The card usually does not suffer much from moisture, but in order not to lose the information stored on it, it is better to dry it too. Also remove the memory card (if any) and try to disassemble the device as much as possible. Remove everything possible without damaging the microcircuit.

IMPORTANT! If the phone falls into water and does not turn on, you can be “congratulated”, you lost him. It is strictly forbidden to turn on the device until it is completely dry. Contacts that may not have burned out yet will burn out. If the phone fell into water and does not work, and you tried to turn it on while wet, you will have to take it in for repairs.

The phone fell into the water, how to dry it

The device will have to dry for at least a day. Quickly drying your gadget with a hairdryer is not a good idea. A powerful stream of hot air can force liquid inside the device, even if it itself did not get there. Moreover, the hot air itself has a detrimental effect on the sensors of a mobile device.
The battery can be placed near the switched on heater. It is better not to place the battery or the entire device directly on the heater. The device itself can be placed in any moisture-absorbing material.


There is an opinion that if a phone falls into water, it can be immersed in alcohol. Alcohol will dissolve moisture in the mobile without harming the microcircuits. You can also place the device in a bowl of rice or Seliko gel, which is placed in a box with shoes. The gadget will need to be left in this position for 2-3 days.


After a day of drying, you can try to turn on the affected device. Most often, timely measures are enough to make the tube “come to life.” If this does not happen and the phone does not turn on, you should think about visiting a service center or buying a new one.

How to fix a phone that fell into water

In the case when all resuscitation efforts to save a cell phone have not brought results, the cell phone does not work, or the screen does not work, the question arises: is it possible to repair a phone that has fallen into the water. It is possible, provided that you understand the structure of gadgets, and after your repair there will be no unnecessary parts left.

If the phone falls into water and the screen does not respond, but the device turns on, return it to dry for another day. If a touchscreen phone falls into water and the sensor does not work after drying, you will most likely have to replace it. Based on the prices for replacing damaged parts, you can already think about buying a new gadget.
If the phone is dropped into water and the speaker does not work, while other functions are normal, the contacts are most likely oxidized. You can try to disassemble the device and clean the contacts. The same can be done if the phone falls into water and does not charge. Provided that you can freely disassemble and reassemble your device. If you are not confident in your abilities, it is better not to take risks.

If disassembling the gadget yourself is problematic for you, you should take it to a service center. A competent technician will professionally eliminate the consequences of “bathing” inside the device. In any case, a repairman who knows the intricacies of repairs will fix problems better than the most well-read user.
It’s worth noting right away that you won’t be able to send a mobile phone that has been in water for warranty repair. Nowadays, most companies that produce phones have equipped them with moisture sensors. And any master will determine this immediately by disassembling the device. When phone fell into water, repair not covered under warranty.
In general, even if neither you nor the technician at the service center managed to save the device, there is still no reason to be upset. What a reason to buy a brand new mobile phone with improved functions. Besides, while the drowned device was being revived, you were used to using another gadget and weren’t particularly worried about it. It's better to take this as a reason to change your life for the better.

In this article we will tell you what to do if your phone falls into water. The information is relevant at the moment because for almost all smartphones that do not have an IP67 or IP68 rating, moisture can cause serious damage. In this case, water begins to flow inside the case, hitting the board, processor and causing short circuits.

First steps to save your phone

If your phone falls into water, you should not panic; it is better to try to remove it from the liquid as quickly as possible. After all, the longer the phone is in water, the greater the likelihood of damage to the motherboard components. Most people in such a situation will immediately begin to press all sorts of buttons to check the functionality of the phone, but this absolutely cannot be done to avoid a short circuit.

However, if the smartphone has a non-removable battery and remains on after the dive, then the first thing you need to do is turn it on using the power button, and if the battery is removable, then immediately remove it from the phone. Along with the battery, you also need to remove the SIM card and memory card. Next, wipe the phone and its removable parts with a dry cloth and make sure there are no liquid residues.

Under no circumstances should you try to dry your smartphone with a hairdryer, nor should you blow into the phone or shake it, as such actions may cause water to get into other components of the device. You can get rid of moisture inside your phone using the following 5 methods.

Isopropyl and ethyl alcohols

For many years, isopropyl and ethyl alcohols have been available and inexpensive products that have been used to clean radio circuit boards. As mentioned earlier, the main reason for device failure is corrosion of the motherboard elements, and isopropyl alcohol contains chemical elements that help prevent this corrosion and remove moisture. Also, their modern analogues are water-based cleaning liquids; such liquids are not conductors of electric current, and their evaporation occurs instantly.

The fact is that when water turns into ice, its molecules have less conductive effect due to the increase in the distance between the molecules, which prevents a short circuit.

If the phone does not turn on the first time, then try repeating the procedure again, and after several attempts your phone will most likely turn on.

However, if you keep your smartphone in the refrigerator, you can get the opposite effect and make the situation worse.

Drying your phone with absorbents

The method is already familiar to many, as it is very popular on the Internet. One of these substances is rice. It's no secret that rice absorbs moisture, and in theory, submerging your phone in a suitable container of rice should do the same trick for it.

This method has an undeniable advantage, since it eliminates the possibility of carelessly turning on the device while there is a large amount of moisture inside it. However, this method does not guarantee complete restoration of the smartphone, because the water contained can cause oxidation of the contacts and elements of the device’s motherboard and, as a result, lead to negative consequences.

Compressed air

The main purpose of this method is to try to speed up the drying process. The best option in this case is a cylinder with compressed air inside. Such cylinders are often used when cleaning hard-to-reach components, computer motherboards and laptops from dust.

To implement this method, pass air using a balloon through various openings of the phone: speakers, microphone, charging connector and audio connector. Cleaning should be focused on the charging port, as it is closest to the battery compartment, which will give you more room for air to move.

Remember that this method is more of a preventative measure and will not eliminate moisture as effectively as possible.

Synthetic dehumidifiers

This solution provides a quick and easy way to rid your phone of water that has gotten into it. On the vast expanses of well-known Internet sites there are many similar accessories for small electronic devices.

Synthetic desiccants are hermetically sealed plastic bags with special granules inside that effectively absorb moisture. The only disadvantage of this method is the cost. In our countries, such accessories are not in great demand, and not everyone would dare to pay 1,200 rubles for them.

Also remember that none of the above methods is a guarantee that your phone will be completely restored. And if first aid for your smartphone is unsuccessful, contact a repair center. We wish that such troubles do not arise in your life!

Have you ever left your phone in your pocket when it rained or forgotten to put it out while doing laundry? Have you ever dropped your phone in the sink?

There are many typical situations that result in water or other liquid getting into the phone, which subsequently, with a high probability, will lead to a complete or partial malfunction of your device. But one question remains - what to do if phone got wet and exposed to liquid?

I remember the first time I dropped my phone in the water. I did not know what to do and therefore I was not able to resuscitate my device.

It is worth noting that liquid getting into a mobile phone is one of the most dangerous situations for it, which may result in the purchase of a new device. But don't panic ahead of time. With a timely response, it can be saved and almost completely restored.

What to do if water gets into your phone:

1. Naturally, first you need to get it out of the water as quickly as possible. In this case, even fractions of a second are important. 20 seconds is enough for the liquid to completely penetrate the body of the mobile device. Of course, it all depends on what kind of phone you have. Some mobile devices are designed for use in harsh conditions and interaction with water does not threaten them. Considering that you have an ordinary mobile phone, you shouldn’t expect high tightness from it (water easily seeps through the small gaps of the case and keyboard).

2. Remove the battery as quickly as possible, even if your phone is turned off. This will prevent short circuits and concomitant electrochemical corrosion of board elements, processor and other microcircuits. In other words, the board and all its elements begin to rust and rot. The longer the corrosion occurs, the more difficult it is to restore your phone. After the battery is removed, wipe the phone's battery connector with a soft cloth or cotton wool. Under no circumstances turn off the device by simply pressing the button; the battery should be removed immediately!

3. Take out the SIM card. Sometimes telephone contacts are much more expensive than the device itself, and besides, I don’t think you should have much interest in restoring numbers. Wipe it with a cloth and put it to dry. The SIM card is practically impervious to water and will almost always remain operational, but there is no such thing as unnecessary safety net.

4. Disassemble your phone down to the last screw. Just don’t forget in what order you did everything, otherwise you’ll have to take it to the service center. Lay out all the parts on a soft cloth and leave to dry for a couple of days. For more efficient drying, you can use a hairdryer, but you should take into account the distance to the parts (when heated, some elements of the board can melt). You need to ensure that the air supplied by the hairdryer is at room temperature. You can also cover the parts with dry rice, they say it helps. Some companies produce special bags for drying devices (for example, Bheestie or Gadget Genie), which are several times more effective than rice, although they cost about $15. The best effect is achieved by properly drying the phone in a so-called ultrasonic bath, which is intended primarily for drowned phones. A special ultrasonic bath solution washes away the remaining salts and oxides that remain even after the device has completely dried. But not everyone has a “miracle bath” at home and therefore has to improvise.

5. If something other than water, such as juice or coffee, is spilled on the phone, you should rinse all parts with clean, preferably distilled water. The main thing is to prevent this kind of liquid from drying out, otherwise it will be very difficult to get rid of it even for masters from the SC. After washing, we leave the phone to dry for a couple of days.

6. After the phone and all its components have dried well, put it back together in the reverse order, insert the battery, pray and press the power button. Most likely, your phone will turn on safely and work if you have read and used these recommendations correctly. In some cases, when turning on and operating, the phone may behave strangely, which is direct evidence that you have not completely dried the parts and there is condensation left somewhere, which causes the device to “sausage convulsively” If, after all, your mobile device refused to turn on - you have a good reason to buy yourself a new phone.

Please note that you do all manipulations with your phone at your own peril and risk. If your phone is drowned, then any warranty will not apply to it.

If it was not possible to restore the device using these methods, you can take it to a service center, but you should not hide the “medical history” of your mobile phone - the technicians will in any case find out that water has got into the phone. Remember that not one of the methods will give you a 100% guarantee of restoring the “drowned man”. Take care of your mobile friend and never drop it into water (they don't like to take baths).